Aquasure water filter is an effective and economical way to provide clean drinking water for your family. Installing a water filter can help reduce the number of contaminants, such as chlorine, lead, and other chemicals, often found in tap water. Installing an Aquasure water filter is relatively simple. It will require some basic tools, such as an adjustable wrench and screwdriver, as well as the appropriate parts to match your existing plumbing system.
Things Required
- Plier
- Wrench
- Screwdriver
- Utility knife
- Tape
- Silicon greases lubricant
How To Install An Aquasure Water Filter?
Step 1: Turn off the main water supply valve: Before installing the water filter, it is important to turn it off.
Step2: Turn the shut-off handle clockwise: Continue turning it clockwise until it reaches its fully open position. This will allow water to flow freely through the main valve.
Step 3: Loosen the nut with a plier: When it is sufficiently loosened, carefully pull it away from the bolt and discard.
Step 4: Separate the cold water tube from the faucet shank: Once you have loosened the packing nut and unscrewed the bonnet nut, carefully pull off the faucet shank from the cold water tube. Put aside any washers or other hardware you might see on it.
Step 5: Attach the feed water adapter to the cold water supply valve: Using the feed water adapter, connect the cold water supply valve to the inlet connector of the reverse osmosis system. Make sure that all connections are securely tightened.
Step 6: Attach the cold water riser to another side of the feed water adapter: Once all the fittings are in place, attach one end of the cold water riser to the other side of the feed water adapter.
Step 7: Remove the reducer from both sides of the feed adapter: Remove the reducer from both sides of the feed adapter by unscrewing it from its mounting bracket. Do this carefully, as the threads on these components can be easily damaged.
Step 8: Power on the control valve: To power on the control valve, manually turn on the electrical breaker or switch. Check to ensure that all lights are on and that there are no loose wires.
Step 9: Connect the power line with the control valve: Now that the control valve is installed, it’s time to connect the power line. Start by securing one end of the power line to the terminal on the control valve and then run the other end up through a conduit and out to an external source. Securely fasten all of your connections using appropriate electrical components.
Step 10: make sure that the screen lights up and shows power: Once you have connected the power adapter and secured it, check that your screen is lit up and showing signs of powering on. Double-check the connection if the screen remains dark or isn’t powered on.
Step 11: Turn on the cold water: turn on the cold water supply valve to ensure that the faucet can access the necessary water supply.
Step12:Allow the water to run for a few minutes: After you turn on the water, allow it to run for several minutes. This will help flush out any debris that may have been stuck in the pipes and fill up the pipes with fresh water.
Six Stages Of Aquasure Water Filter
1. Clarity Cartridge: The first stage of the filtration process is a clarity cartridge that captures visible sediment from the water. This cartridge should be replaced regularly to maintain effective filtration.
2. Chemi-block: This chemical filter is designed to remove chlorine, pesticides, and other chemicals from your water. The Chemi-Block should be installed between the cold water line and the water heater.
3. Membrane life enhancer: Connect the membrane life enhancer to the inlet of the membrane housing. Make sure it is properly connected.
4. Reverse osmosis cartridge: The reverse osmosis cartridge, also known as the “RO” filter, is designed to remove contaminants from water by forcing it through a membrane. This type of filter is often used in municipal water systems and some cases can be installed on a home’s central plumbing system.
5. Mineral cartridge: The mineral filter cartridge in an Aquasure water filter is designed to remove chlorine, heavy metals, and chemicals from the water, making it safe for drinking.
6. UV disinfection Chamber: This is an optional feature in Aquasure water filters. It uses ultraviolet radiation to kill bacteria and other microorganisms, providing a deeper level of purification. It should never be operated without water present in the filter tank.
What Does The Aquasure Water Filter Remove?
Removes dirt and sand from water: Aquasure water filters are designed to reduce dirt, rust, and sand particles found in tap water. It also effectively removes chlorine and other synthetic chemicals used to treat municipal water supplies.
Increase the level of calcium and magnesium: One of the benefits of installing an Aquasure water filter is that it can increase the levels of calcium and magnesium in your drinking water. This helps to improve taste and texture, as well as providing essential minerals for overall health.
Eliminate water-borne diseases: Aquasure water filters can help eliminate many water-borne diseases that are prevalent today.
It removes hardness and heavy materials from water: Aquasure water filters are designed to remove hardness and heavy materials from your water, improving the taste, odor, and clarity of the water. Aquasure filters use ion exchange technology to remove minerals, such as calcium and magnesium, which contribute to the hardening of the water, making it less palatable.
Prevent scaling of salts: If you live in a complex water area, it is essential to replace the filter cartridges regularly. This will help prevent the scaling of salts and keep your drinking water clean.
Tips
Do not lubricate the threads during installation: Lubricants such as soap, oil, or grease might seep into the filter and contaminate your drinking water. Also, ensure you’re using a wrench to install the canister tightly.
Do not use tools to tighten the valve: Do not use tools if you can screw the valve with your hands. Using tools to tighten the valve can damage it, so ensure that you only use your hands to secure it tightly.
The filter can be damaged if connected to hot water: When installing an Aquasure water filter, it isessentialt to avoid connecting it to hot water as this can damage the system.
Make sure that tap water pressure is between 4.26psi and 42.6 psi: For optimal performance, the Aquasure water filter must be hooked up to a water line with a tap water pressure between 4.26psi and 42.6 psi (29 kPa and 294 kPa). If the incoming pressure is not within this range, an adjustable or non-adjustable pressure regulator will be needed.
Avoid installing filters outdoors: The Aquasure water filter should be installed indoors. Installing the filter outdoors can expose it to extreme weather conditions, which can cause damage and affect the filter’s performance.
Clean the storage every 30 days: It is important to remember that it is necessary to clean the storage tank of your Aquasure water filter every 30 days.
Troubleshooting
Water tastes terrible: Check whether all connections are tight if the water still tastes bad after installation. The Taste and Odor Cartridge can also cause this problem. Replace it with a new one or rinse it if it has not been used for a long time.
Little water being purified: Check the connections and ensure they are firm. Additionally, check that the filter is clean and free of debris or blockage. Also, ensure that the water pressure going into the filter is adequate for proper operation.
Water does not come out: Make sure all connections are tight and check for any blockage or debris in the filter. Additionally, ensure that the water pressure going into the filter is adequate for proper operation.
Water is leaking: If the water is leaking, first make sure all connections are tight. Check for any cracks or tears in the filter housing if the leaking persists. Replace the filter if necessary.
FAQs
Should a pre-filter be used in a water filter?
Yes, a pre-filter is recommended when installing a water filter. A pre-filter can help reduce the contaminants in the water and make it easier for the the primary filter to do its job.
Can I install an RO purifier for tap water?
Yes, you can install an RO purifier for tap water. An RO purifier is a great way to reduce the number of contaminants in your drinking water.
Why does the green light of my filter blink?
If your Aquasure water filter’s green light blinks, it is not functioning correctly. This could be due to a low battery or clogged filter cartridge. Check if the batteries are adequately charged, and then check if the filter cartridge needs cleaning or replacement.
Why is my water purifier releasing warm water?
If your Aquasure water filter releases warm water, it could be caused by several factors. The most common cause is a buildup of sediment in the filter or an obstruction in the tubing that connects the cold and hot water lines to the machine.
What is the cost of the Aquasure water filter?
The cost of an Aquasure water filter will depend on the model and features you are looking for. Generally, Aquasure filters range from around $50 to over $200, depending on the type of filtration system you purchase.
Which is better, the aquaguard or the Aquasure water filter?
The answer to this question largely depends on your individual needs and preferences. Aquaguard water filters are known for their advanced filtration technologies and high-end features, while Aquasure filters typically offer more basic filtration capabilities at a lower price point.
Conclusion
Aquasure water filter installation is a simple, straightforward process. For installation, it should take no more than an hour to complete. Keep your filter clean and change the cartridges as manufacturer guidelines recommend. With proper maintenance, your Aquasure water filter will give you pure and safe drinking water for years to come.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.