Installing a Home Master water filter is a great way to ensure that you and your family access clean, safe drinking water. Installing the Home Master Water Filter System is simple. Generally, installation involves setting up the water line connections, attaching the filter housing to the wall or countertop, connecting your existing plumbing to the filter system, activating the filter cartridge, and turning on your main water supply.
What Is A Home Master Water Filter?
A home master water filter is a filtration system that uses mechanical and chemical processes to remove contaminants from drinking water. The filter typically consists of several stages, including pre-filtration, carbon filtering, and reverse osmosis. Each stage removes different impurities from the water and ensures clean and clear drinking water is delivered to your home.
Things Needed For Installation
- Safety glasse
- Towel
- Screwdriver
- Wrench
- Hacksaw
- Power drill
- Teflon tape
- Torch
Parts Required For Installation
Shutoff valves: Shutoff valves help to shut off the water supply during the installation of a home water filter system.
Bypass valve: This is an essential part of any home water filtration system as it allows you to switch between filtered and unfiltered water without removing the filter.
Hex nipples or pipe nipples: Hex nipples are short pieces of metal piping with a hexagonal head and two threaded ends that can be connected to other pipes by tightening a fitting over the top. Hex nipples may be used to extend an existing pipe or connect two pipes with different diameters.
Pressure gauge: This device will help determine how much water pressure is in the system. It can also alert you when any changes in pressure might indicate an issue with your water filtering system.
Pipe unions: Pipe unions are necessary for easy installation and maintenance of the filter without cutting the pipes.
Pressure regulator: A pressure regulator is essential to a home master water filter. It helps maintain the desired water pressure going into the filter unit so that it functions optimally.
Ground jumper cable: Ground jumper cables are electrical wires that provide a direct path for the flow of electricity between two points.
How To Install A Home Master Water Filter?
Turn off the main water supply: Before starting, make sure to turn off the main water supply. It is essential to completely shut off the incoming water pressure to avoid possible leaks during the installation and operation of your Home Master Water Filter.
Open all plumbing fixtures: You need to open all the plumbing fixtures in your home, such as sinks, showers, and toilets. This will allow water to enter your new home master water filter system more efficiently.
Drain the lines as much as possible: If replacing an existing filter, turn off the water and drain the lines as much as possible. You can do this by running all of your cold water faucets until no more water is coming out. This will ensure that no dirty water will get into your new system when you disconnect the old filter.
Measure the area: The critical step to installing a home master water filter is to measure the area where it will be installed. Make sure that you have enough space and clearance for the filter. To install the filter, you’ll need access to cold and hot water lines with shutoff valves and an electrical outlet for powering the motor.
Cut and remove a section of the water line: After measuring the area, cut and remove a section of your existing water line. You must turn off the home’s main water supply before cutting. Please measure the length of the new filter, mark it onto your existing water pipe, and then use a tubing cutter or saw to cut.
Place a shutoff valve: Place a shutoff valve on the pipe. This will allow you to turn the main water line on and off without turning it off at the source, such as your city’s supply or well pipe.
Use mounting brackets: Before you install the Home Master Water Filter, make sure you have mounting brackets ready to mount securely. Mount the water filter securely on brackets.
Adjust pipe length: Cut the pipes according to the length you need for a tight fit. Be sure to leave some extra space in case of minor adjustments are needed during installation.
Fit a pipe into the cut section: Once you have cut the pipe, fit the pipe into the cut section. Make sure to make an even connection with no gaps or spaces between the two sections of the pipe.
Fit pipe union and shutoff valve: When you have the filter in position, install a threaded pipe union and a shutoff valve on each side of the filter. Use adjustable wrenches to tighten the unions securely.
Use teflon tape on fittings: It is essential to use teflon tape on fittings when installing a home master water filter. Teflon tape, also known as plumber’s tape, helps create an airtight seal between the filter and pipes, thus preventing leaks.
Fit shutoff valve and filter together: Fit the filter and shutoff valve together by connecting the threads of the two pieces. Tighten them until they are connected securely, but do not over-tighten them, as this may damage their connection.
Fit pipe hanger: The next step in installing a home master water filter is to fit the pipe hanger. The pipe hanger is designed to hold the filter securely and should be placed near the main water supply.
Fit the shutoff valve on the outside of the filter: You will need to fit the shutoff valve on the outside. Connect one end of the tubing to your water main outlet port. Make sure that it is secured firmly before continuing. Connect the other end of the tubing to the inlet port on the filter housing.
Turn the water supply on. Turn the cold water supply on full and flush out any sediment from the pipes before you install.
Changing The Home Master Water Filter
Turn off the water supply to the system: First, turn off the water supply to your Home Master system by turning the main shutoff valve counterclockwise.
Depress the red pressure release button: Insert a flathead screwdriver into the button and turn it counterclockwise to depress it. Once depressed, hold the button down for 15 seconds before releasing it.
Unscrew the housing: Before installing the Home Master water filter, unscrew the system’s housing and place it on a clean surface. Use gloves when handling the filter casing, as dirt particles can contaminate your drinking water.
Remove and discard old filter cartridge: For installing a home master water filter, remove and discard the old one.
Scrub the sump and cap with warm water: Before installing the home master water filter, it is essential to clean the sump and cap with warm water. This will ensure that all dirt and dust particles are removed from these components before they are connected to the water line.
Lubricate the O-ring: Before you install the Home Master water filter, make sure to lubricate the O-ring with silicon or Vaseline. This will help ensure a tight and secure connection between the two pieces.
Remove filter packaging: Locate the filter inside its packaging and remove it. Make sure to discard the packaging properly.
Insert new filter cartridge: Once the housing is removed, you will need to insert a new one. Make sure that all parts of the old one have been removed.
Fit the bottom of the housing into the cap: Place the bottom part of the water filter housing into the cap, ensuring the seal is in place. Secure it by tightening the two screws on either side of the housing.
Turn on the water supply: Before commencing installation, turn on the main water supply.
Flush the system: After installing the filter, it is essential to flush the system by running water through it for several minutes. This will help clear any debris or sediment that may have been stirred up during the installation process.
Troubleshooting
Leaks from metal fittings: The nuts should be tightened with a wrench if water leaks from metal fittings. If tightening doesn’t help, it is recommended to replace the faulty fitting.
Leaks from plastic fittings: The plastic fittings used to connect different parts may wear out over time and create leaks in the water filter. Inspect them regularly for any damage and replace them when necessary.
Leaks from push-pull or quick-connect fittings: If you’re using push-pull or quick-connect fittings, it’s essential to ensure no leaks. To do this, first, use seals and gaskets that are designed for the specific size of your pipe. Screw the fitting into place but don’t overtighten it – doing so can damage the gasket and cause a leak.
Fine Air Bubbles/Grey-Tinted Water: If you notice fine air bubbles or grey-tinted water coming from your home master filter, there is likely a problem with the installation. If this occurs, shut off the main incoming water supply and disconnect the filter from all piping. Check for any signs of leakage in the hoses and fittings attached to the unit, looking for splits, cracks, or other signs of wear and tear. If any leaks are found, replace the damaged parts before reinstalling the filter.
Noises: Installing a home master water filter is relatively easy. The first step is to identify the right place to mount the filter. Check for potential noises around the placement area, such as pipes running through walls or other plumbing equipment. Make sure that the noise generated by these items will not interfere with your filter’s operation when mounted.
FAQs
Does the RO system produce wastewater?
Yes, the RO system does produce wastewater. The amount of wastewater produced depends on the type of filter used and the quality of input water. Generally, a good quality reverse osmosis membrane can reject up to 99% of total dissolved solids from the input water and produce 1-2 gallons of wastewater .
Can I mount the home master RO in the basement?
Yes, the Home Master Reverse Osmosis (RO) system can be mounted in a basement. It is essential to ensure that any connections downstream from the RO unit are located above the flood level of your basement.
Can I connect it to my kitchen faucet?
You can easily connect the home master water filter to your kitchen faucet.
How often do you change the whole house water filter?
It is recommended to change the whole house water filter when there is a reduction in water pressure, or at least every 12 months, for optimal performance. The best way to determine if your filter needs replacing is by doing a Water Pressure Test and Flow Rate Test.
Conclusion
Installing a home water filter is an easy and cost-effective solution to ensure that the water you drink is safe and free of contaminants. It will give you peace of mind and save you money in the long run by reducing your need to buy bottled water. Although there are many types of water filters available, installing a whole-house master water filter is the most efficient and economical way to ensure that your home’s entire water supply is free of contaminants.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.