Installing a Pelican brand whole house water filter is often necessary to reduce the amount of sediment, minerals, and other contaminants in your household’s water supply. This type of water filter passes all incoming water through a series of filtration media that help trap and remove any particles that could be causing problems. The installation process is relatively straightforward, but it’s important to make sure you understand each step before beginning.
What Is A Pelican Whole House Water Filter?
Pelican’s whole house water filtration system filters out sediment, chlorine, and other contaminants in your home’s electricity. It also reduces unpleasant odors and tastes, increases the life of water-using appliances, and provides healthier drinking water for your family.
Parts Of Pelican Whole House Water Filter
- Pelican whole house water filter
- 1″ Plastic male NPT assembly
- Sediment filter system
- Two bypass valve
- hose bib assembly
- Mounting brackets
- Head screws
- washers
How To Install A Pelican Whole House Water Filter?
1. Pre-installation- Bypass valve installation:
Attach a garden hose to the hose bib assembly: Use the ½-inch garden hose to connect the inlet side of the bypass valve to the outlet on your house’s primary water line. Tighten all clamps and connections until snugly secured.
Connect hose bib assembly to bypass valve: Find the bypass valve and remove the protective cap. Thread one end of the hose bib assembly onto the inlet port on the bypass valve and tighten by hand.
Fill the pelican whole house filter: Fill the pelican whole house filter with water. Fill it to the top of the filter, about 12-16 inches from the bottom. The water should be slightly warmer than at room temperature.
Turn the water off: Before beginning the installation process, it’s essential to ensure that you have shut off your main water supply. Opening up a faucet anywhere in the house would be best; let the water run until it stops flowing, and then close it again. This will help ensure that any sediment or other particles are flushed from the piping.
Remove the garden hose from the hose bib assembly: Unscrew the garden hose from the hose bib assembly located at or near your water source. Gather all necessary parts and tools for installation, including a cut-off tool if you will be cutting copper lines.
Allow the carbon tank to soak for 48 hours: Soak the carbon tank for at least 48 hours. This will allow the carbon inside to expand fully, ensuring optimal filtration performance. During this time, check periodically to ensure the tank is completely submerged.
2. House bib assembly:
Reattach the garden hose to the hose bib assembly: Reattach the garden hose to the hose bib assembly located at or near your water source. Make sure that all connections are tightened securely.
Slowly turn on the water: Start by slowly turning on the water, allowing it to get used to the filter before sending it through your plumbing system.
Run the water through the bypass valve for 30 minutes: Once the filter has been securely attached to the pipes, you will need to run the water through the bypass valve for at least 30 minutes. This allows any air or contaminants that may have been in the system to be flushed out.
Turn off the water: Now turn off the main water supply of your home through the cut-off valve.
Remove the hose bib assembly: Remove the hose bib assembly by turning off the water supply to the house and opening a faucet downstream of the valve. Unscrew the hose connector with your hand or use a wrench if needed.
Disconnect the garden hose: Remind the garden hose from the faucet before installing a pelican whole house water filter.
3-Filter assembly :
Unscrew the cover of the blue filter housing: Unscrew the cover of the blue filter housing and remove it.
Remove the covering from the Sediment: Carefully remove the cover of the sediment filter with a screwdriver. Make sure you do not damage any other components in the process.
Place the Sediment Filter onto the Stand Pipe: The sediment filter should be placed onto the standpipe, a tube that allows water to flow into the filter.
4-Filter installation :
Shut off the water: The first step to installing a pelican whole house water filter is to shut off the water supply. This will prevent any water from running out of the pipes while you are working on it.
Attach the Filter Cover to the Mounting Bracket: Hold the filter cover against the mounting bracket. Use a screwdriver to attach it in place with the screws provided.
Attach the Mounting Bracket to the wall: Once you have the mounting bracket ready to go, attach it to the wall. As with any DIY project, use a level to make sure your line is straight and secure the bracket with screws. Make sure that when attached, the open end of the filter is facing downwards so that gravity can help you pour in water for later filling.
Tighten the blue filter housing: Make sure the filter housing is tightly connected to the cold water pipe under your sink. Place the wrench around the hexagon portion of the blue filter housing and turn clockwise until tight.
Determine the size of the water supply line: You must determine the size of your water supply line to ensure that you purchase the correct parts. To do this, measure the outside diameter of your copper pipe and check it against a chart to determine its size.
5-Tank installation:
Level the pelican: After the tank has been connected to the water supply line, it must be leveled using a spirit level.
Fit the bypass valve: Thread the bypass valve onto the outlet side of the filter chamber. Ensure that the bypass valve’s O-ring is in place and secure. Use a wrench to tighten the valve, taking care not to over-tighten.
Connect the water supply to the bypass valve: Connect the water supply line to the bypass valve. The bypass valve can shut off water flow from the filter when it needs maintenance or repairs.
Connect the outgoing water supply to the outlet: Turn off the main water supply and make sure it is turned off by turning on a faucet connected to the system. Connect the outlet of the Pelican Whole House Water Filter System to your existing water supply using flexible PVC piping or copper tubing, depending on which type you opted for during installation.
Check for leaks: To ensure that your new water filter is installed correctly, you should check for any leaks.
Troubleshooting
Water leaking at the top of the tank around the head: Check that the O-ring is seated correctly and that all connections are secure. If necessary, tighten it with a wrench. If the water continues to leak, replace the o-ring.
The tank leans to one side or is not level: If the pelican whole house water filter tank is not level, it will affect the water flow into the tank. To ensure your tank is leveled correctly, you should adjust the support base until the bubble on a spirit level is perfect.
Water pressure is slowing: The water pressure in your house may decrease due to sediment build-up in your pipes or a malfunctioning pump. Installing a Pelican whole-house water filter could be tricky if this is the case. Make sure to check your water pressure before you begin installation and then adjust accordingly.
Water appears grey or cloudy: If your water appears grey or cloudy after installing the pelican whole house filter, it is likely because of air in the system. This is a common occurrence with any new filtration system and can bequicklyy resolved by simply bleeding out the air from the filter housing. To do this, turn on each faucet connected to the filter system one at a time, starting with the highest faucet and working your way down. Once the water begins flowing from each faucet, the air should be bled from the system, and your water should run clear.
Water pressure is slowing immediately after installation: If the water pressure is slowing immediately after installation, it could be due to a clogged filter cartridge. Check for any blockages in the filter cartridge and clean it if needed. It may also help flush out your home’s plumbing system by running hot water throughout your faucets for several minutes before using the filter.
FAQs
What does a water filter remove from the tap water?
A water filter can remove contaminants such as sediment, heavy metals, chlorine, and other chemicals. It can also improve the taste of tap water.
Where should a whole house water filter be installed?
A whole house water filter should be installed for your home’s water supply at the point of entry. This is typically just after the main shutoff valve or behind the meter, usually in a utility closet, basement, or outside near an exterior wall.
Do I need to boil water if I have a whole house water filter?
No, you do not need to boil water if you have a whole house filter installed.
How much does it cost to install a Pelican whole house water filter?
The cost to install a Pelican whole house water filter varies depending on the type and size of your filter. Generally, you can expect to pay between $200-$500 for installation.
Conclusion
A pelican whole house water filter is a great way to ensure the safety of your home’s water and protect your family from contaminants. Installing a filter can be done in just a few simple steps, but it’s essential to ensure that you take all necessary precautions. Make sure that all connections are properly sealed to avoid any water leaks.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.