Aqua-Pure is a water filtration system that connects directly to your home’s water supply. Installing an Aqua-Pure system can help reduce contaminants like sediment, chlorine, rust, lead, and other potentially harmful particles in your drinking water. Installing an Aqua Pure Water Filter can be a quick and easy process that ensures your home is supplied with fresh, clean water at all times.
How To Install An Aqua Pure Water Filter?
Determine system location: If you determine the system location to be beneath the sink, a hole must be drilled to access the water line. No additional holes are needed if the placement is elsewhere, such as beside the sink or near a water line.
Prepare area for installation: Before installation, decide on the most convenient location to install your Aqua Pure Water Filter. Make sure you choose a place that is easily accessible and close to the main water supply. Additionally, ensure enough space for the filter and mounting hardware.
Install the faucet adopter and tubing: Unscrew the aerator at the end of your faucet and attach the faucet adaptor, which is included with your filter kit. Measure and cut your tubing to the desired length. Then slide one end of the tubing onto the faucet adaptor until it is secure, and insert the other end of the tubing into the inlet of your filter. Secure with a compression nut.
Prefill and sanitize the storage tank: Once the filter is secured, it’s essential to prefill and sanitize it. This ensures that the water filtration system can perform effectively. To do this, fill the tank with a clean water solution and chlorine bleach or hydrogen peroxide at a ratio of 1 tablespoon per gallon of water.
Install the drain connection: Unscrew the drain connection from the bottom of the Aqua Pure filter and attach it to a nearby drain line with a nut and compression washer. Ensure the rubber gasket is in place before tightening the nut and washer onto the drain line.
Make the faucet mounting hole: Use a 1/4-inch drill bit to make a hole in the sink or countertop and install the mounting sleeve. Secure the mount onto the sink or countertop with screws.
Mount the faucet: Ensure you have the right mount type before installing the filter. Most Aqua-Pure filters come with an included mounting bracket to secure the filter to your faucet.
Install the RO assembly and storage tank: Connect the RO assembly to the cold water line using the provided T-fitting. Ensure the pressure relief valve points away from you and toward a drain or sink. Secure the RO assembly with locking pliers, then tighten it until it is firmly in place. Use a wrench for extra leverage, if necessary.
Make final tubing connections: Push tubing onto the outlet port of the filter head and the inlet port of the faucet adapter. If necessary, secure with a hose clamp.
Install filter cartridges: Once you have installed the filter housing, now install the filter cartridges. You must install one or two cartridges depending on your specific filtration system. Generally, when using a dual-cartridge filter system, the first cartridge should be a sediment filter, while the second should be a carbon block filter.
Start-up system: Once the filter is installed, it is essential to start it. First, ensure all connections are secure and there is no water pressure in the line before beginning. Turn on a faucet downstream of the filter to let air enter the line. Next, turn off this faucet and open any valves above or below the filter.
When to replace the aqua pure water filter?
Every six months: It is recommended that Aqua Pure Water Filters be replaced every six months to ensure they are operating optimally and filtering the water properly. This will also help extend the life of your appliance, as older filters can become clogged and require more frequent replacements.
A decrease in water quality would be an indication: If you notice a decrease in water quality, such as it tasting or smelling bad, this could indicate that the filter needs to be replaced. Additionally, if sediment or rust particles are in the water, this should also trigger a replacement of your Aqua Pure Water Filter.
When a reduction in flow rate occurs: Another indication that the filter is ready to be replaced is when you notice a decrease in flow rate. This could mean that the filter has become clogged and needs to be changed quickly to maintain good water quality.
How To Replace Pre-Filter And Post-Filter Cartridges?
Lift the faucet handle: Turning it to the on position diverts water through the filter.
Turn off the cold water: Before beginning the installation process, turn off the cold water line connected to your sink. This will prevent any leaks or other problems from occurring during installation.
Twist the filter cartridge counterclockwise: The filter cartridge will come loose and can be removed. Make sure to dispose of the used filter cartridge according to local regulations.
Pull cartridge from the head: Once the head has been removed, you can pull out the water filter cartridge and discard it. To do this, grasp the cartridge’s handle with your hand and twist gently to unlock it before pulling it straight out. Clean any debris from inside the housing.
Wet the O-Rings seal: Before installing the filter, wet the O-Rings with water. This helps them form a seal and prevents any leaks. Make sure to use clean water when doing this.
Twist counterclockwise to lock into place: The filter should fit snugly but not too tight. Next, locate the water supply valve under the sink and turn it clockwise to the “On” position. After allowing the water supply line to fill up, test the connection by turning on the cold water tap.
Open the cold water feed valve and check the leaks: Ensure that the cold water feed valve is open. This can be done by turning the handle counterclockwise until it stops, then back one-quarter of a turn to open the valve. After this, you should check for any leaks in your plumbing system at the points where the filter was attached. If leaks occur, you should use pliers or a wrench to tighten the connections and stop any water loss. If necessary, add extra sealant to ensure the connection is secure.
Installation Troubleshooting
Water leaks from openings: If you notice water leaking from any openings, check that the washers are firmly in place and the filter is adequately secured with the locking nut.
If these steps do not stop the leak, it may indicate a faulty connection. Disconnect the filter and apply pipe thread sealant to all threads before reconnecting and securing with locking nuts.
Water pressure is low: If the water pressure is low, this may be due to a clogged filter or incorrect installation. Check that all components are clean and properly attached. Then, increase the filter’s throughput by increasing the water pressure input.
Noise in the drain: If the drain line makes a loud noise when the filter operates, this could be due to air in the system. To reduce or eliminate the noise, open a faucet downstream from the filter until water runs smoothly through the drain line and all noise stops.
The system is not producing water: Check all connections for proper engagement and make sure that the filter’s inlet pressure is adequate. If these steps do not solve the issue, disassemble the filter to check for blockages inside. Clean or replace any parts as needed before reassembling.
Safety Tips
Do not install an aqua water filter near electric wiring: Aqua water filter has many electric components and can cause electrical hazards if installed near any electric wiring.
Do not overload the power outlet: Too many devices connected to a single power outlet might be dangerous. Make sure you use the correct voltage for your aqua water filter and that it is the only device connected to that particular power outlet.
Wear safety glasses during installation: Aqua water filter installation may involve working with sharp objects and materials, so it is essential to take proper safety precautions. Wearing safety glasses will protect your eyes from any flying particles or splashes of liquid.
avoid installing a water filter where the temperature goes to 110 Degrees fahrenheit: Installing a water filter in an area with too much heat can damage the system, so choose a location that does not exceed 110 fahrenheit.
FAQs
Should I install a water purifier or use a traditional water filter?
If you want to reduce impurities in your water, a water purifier is the better option as it uses advanced filtration methods to remove more contaminants than traditional units. However, if cost is an issue or you only need essential filtration of sediment and chlorine, a traditional water filter may be sufficient.
Should a pre-filter be used in a water filter?
Yes, a pre-filter can be used in some water filter systems to reduce particulate matter before it reaches the central filtration system. This can help prolong the life of your water filter and improve its overall performance.
How do you get rid of an airlock in a water filter?
An airlock occurs when trapped air is in the water filter system, preventing smooth flow. To clear this blockage, reduce the water pressure by turning off the main supply and disconnecting the hoses at either end of the filter. You can open a nearby tap to let out any remaining air before reconnecting the hoses and switching the main supply back on.
Can I install an aqua water filter at 45 degrees instead of vertically?
Yes, aqua water filters can be installed at any angle between 0-45 degrees. However, it is best to install the filter vertically for optimum performance, as gravity will help maintain pressure and reduce energy loss. Additionally, the vertical installation helps ensure that sediment remains in the filter housing instead of entering the pipes.
Can I use it for commercial ice machine application?
Yes, an aqua water filter can be used for commercial ice machines. To ensure the best performance, it is essential to use a filter that has been designed to remove chlorine, minerals, and other contaminants from your water supply before it reaches the machine.
Conclusion
Installing an Aqua-Pure water filter can help improve the quality and taste of your drinking water. It provides you with greater peace of mind regarding the quality of your drinking water and reduces maintenance costs associated with other filtration systems. Installing an Aqua Pure filter is a straightforward process that anybody can do in a matter of minutes without the help of a professional. With proper maintenance, an Aqua Pure filter can provide your home with clean and tasty water for years to come.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.