Aquacrest water filters are designed to reduce contaminants in drinking water. They use a combination of activated carbon, sediment, and polypropylene fibers to filter out chlorine, chemicals, heavy metals, and other impurities from the water. Aquacrest filters are compatible with most refrigerator models and can be used with standard and reverse osmosis systems.
Installing your new Aquacrest water filter is a simple process that will ensure you have clean and fresh-tasting water in no time. To install an Aquacrest water filter, start by determining your type of filter. Make sure it is compatible with your refrigerator model. Then locate the existing filter and unscrew it from the connection port.
How To Install Aquacrest Water Filter?
Shut off the cold water: To install the Aquacrest water filter, you must shut off the cold water supply valve that leads to your sink.
Turn on the refrigerator water dispenser: Switch on the refrigerator water dispenser to get access to the water line.
Release the water pressure from the drain line: release the water pressure from the drain line. Shut off the main water supply and open all your home or office faucets. This will ensure no additional pressure when installing your new filter. After the pressure has been released, attach the filter housing to the main water line using a compatible connector. Make sure to tighten all connections with an adjustable wrench.
Remove the existing filter by rotating it counterclockwise: Begin by turning off the cold water supply to your refrigerator. Then, locate the existing filter and remove it by rotating it counterclockwise. Once removed, discard the old filter according to local regulations.
Remove the packaging and sanitary end-cap from the new filter: Before installing the new filter, remove the packaging and sanitary end-cap from the filter. This can be done by twisting off the cap or cutting through it with a pair of scissors. Once removed, discard it safely.
Apply slight upward pressure: After inserting the filter into the holder, you’ll need to apply slight upward pressure. This helps ensure the filter is correctly seated in the holder and won’t lose during water filtration.
Rotate the filter clockwise: Once you have removed the old filter, insert the new Aquacrest water filter. Make sure that it is firmly in place, and then rotate it clockwise until it locks into place.
Ensure the filter is fully installed at 1/4 turn: Once the Aquacrest Water Filter is installed, it must be fully tightened to ensure a proper seal. To do this, twist the filter 1/4 turn after it is firmly in place.
Dispense water into the glass: turn the water on and fill a glass with cold water. This will be used as a reference for later testing filtered water to taste.
Check the filter for any leaks: Inspect the filter for any visual signs of damage or leaks. If you find any, contact your water filtration provider for a replacement filter before installing it.
How To Install Aquacrest Pitcher Filter?
Remove the old filter: Start by turning off the water supply to your fridge. Once the water has been shut off, locate the filter housing and unscrew it. Carefully remove the old filter and discard it.
Open the packaging of the new filter: Carefully open the packaging of the new filter. Make sure not to damage it as you open it.
Shake the filter gently for 10 seconds: This will help to spread the activated carbon particles evenly inside the filter, ensuring maximum filtration.
Fill the bowl with cold tap water: To begin, fill up the bowl with cold tap water. This will ensure that the filter is immersed in clean and filtered water when you put it in.
Place the filter into the bowl: Gently twist it into the bowl clockwise until it stops. Before tightening, make sure that you align the colored dot on the filter with the colored arrow inside the bowl. Tighten by hand to make sure it is securely in place.
Push down and submerge into a bowl: Air bubbles will release: Once you have all the necessary hardware, it’s time to install your Aquacrest water filter. Start by filling a bowl with cold water. Push the filter and submerge it in the bowl until the air bubbles stop releasing. This will make sure that there is a tight seal between the filter and your faucet.
Leave to soak for 15 minutes: After you’ve gathered all the pieces of your Aquacrest filter, it’s time to prepare it for installation. Start by filling a bucket with cold water and soaking the filter in it for 15 minutes. This will help remove air from the cartridge and prime it before installation.
Remove the filter from the bowl: To remove it, grab the top handle and turn it counterclockwise until it is loosened. Pull out the filter slowly to avoid spilling any water.
Install new filter: Insert your new Aquacrest water filter into the bowl. Turn clockwise until you feel the filter is securely in place.
Rinse the filter under the tab: Once the filter has been inserted into the water system, it is essential to take a few moments to rinse it out. This will help ensure that any dust or particulate matter in the filter has been flushed away and that your water is free from contaminants. To do this, turn on your cold water tap and let the water flow through the filter for a few minutes.
Turn off the cold water tap: Once you are satisfied with the water flushed through the filter, turn off the cold water tap. This will help to ensure that any remaining particulate matter is stopped from entering your water system and that you are not using more water than necessary. Additionally, this step will help prevent unnecessary wear and tear on the filter itself.
Fill the pitcher with water: Before using your Aquacrest water filter, fill the pitcher with cold tap water. Gently pour the water into the pitcher, ensuring not to overfill it. Once complete, set aside a few moments to allow air bubbles to disperse from the reservoir and the filter itself.
Place the filter in the pitcher: To install your Aquacrest Water Filter, remove all the parts from the packaging. Place the filter in the pitcher and ensure it fits securely. Twist clockwise until you hear a clicking sound which indicates that it is correctly installed. If you have difficulty inserting or securing your filter into the pitcher, refer to manufacturer instructions for additional help.
Attach the lid to the pitcher: Attach the lid to the pitcher by inserting and securing the filter into the pitcher. To ensure a secure fit, use both hands to twist clockwise until you hear a clicking sound that indicates that it is correctly locked in place.
Allow the water to filter through: After attaching the filter to the faucet, open it and let it run for a few seconds.
Discard the water and repeat twice: Discard the water from the filter by opening the faucet and running it for a few minutes. After that, repeat this process twice to ensure all carbon particles have been flushed out properly, leaving your filter ready to use.
Ensure that the filter is properly flushed: Before installing your Aquacrest water filter, it is essential to flush it properly to clear out any dust or dirt that may have been collected during shipment.
Replace the filter every sixty days: The Aquacrest water filter is designed to provide you with the freshest and cleanest possible drinking water. With frequent use, it’s essential to replace the filter every sixty days to ensure that you have the best-tasting water available.
Maintenance Of Aquacrest Water Filter
Replace your filter every six months: Depending on the water quality and usage, you should replace your Aquacrest filter every six months. If you notice a decrease in the flow rate or an odd taste or smell to your water before this period, it’s time to change the filter.
Release 300 gallons to prevent bacteria and fungus growth: If your Aquacrest water filter has been sitting idle for more than two weeks, you should flush out 300 gallons of water to prevent bacteria and fungus growth.
Keep the new filter in a cool and dry place: If you are not using it, store it in a cool and dry place. Avoid direct sunlight and moisture to prevent any damage or contamination.
Do not use an aquacrest water filter under 32 degrees F: Aquacrest water filters should not be used in temperatures below 32 degrees Fahrenheit. Doing so could cause permanent damage to the filter and reduce its effectiveness.
Clean filter exterior as needed: Make sure to keep the exterior of your Aquacrest filter clean. Wipe it down periodically with a damp cloth and warm, soapy water to ensure dirt and debris don’t build up.
Troubleshooting
Water is leaking out of the pour try: Check to ensure the filter is correctly locked into place. Use a wrench to tighten the installation tube if needed.
The indicator light stopped working: Check to ensure the filter is locked correctly. Make sure the indicator light and power switch are securely connected. Replace if needed.
Water flow is too slow: Check that all connections are secure, with no visible kinks in the pipes or tubes. Clean out any dirt or debris from the filter’s housing. Replace or clean the filter if needed.
Water has an unpleasant odor: Check for any visible signs of corrosion on the installation tube, filter, or tank. Clean and replace as necessary. Ensure all connections are secure and free from dirt, dust, or other debris. Clean the filter if needed.
FAQs
Why is it difficult to twist the filter into the housing?
The filter can become challenging to twist if the O-ring is not correctly aligned with the groove in the housing or if there’s a buildup of debris on either the housing or filter threads.
Where should I install the inline water filter?
To install the Aquacrest inline water filter correctly, finding an appropriate spot in your home is essential. Typically, the filter should be installed at the cold-water line closest to where you will use it.
How long should you run the water after installing the new filter?
Once the filter has been installed, running the water for 3-5 minutes before use is recommended.
Should my filter be under the water?
No, the filter should not be under the water when installed. When you’re ready to install your Aquacrest Water Filter, ensure that the threads on the top of your filter line up with the threads on your device.
How long can water sit in the filter?
Water should not sit in the filter for more than 48 hours. If it does, replace the filter with a new one and flush it thoroughly with cold water before use.
Conclusion
Installing an Aquacrest water filter is a great way to ensure that your family’s drinking water is clean and safe. The installation process may vary depending on your filter type, but it takes only a few minutes overall. Always read the instructions carefully before performing any steps associated with the installation process.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.