Installing a new water filter is essential to maintain your water quality. A New Wave Enviro Water Filter will not only provide clean and safe drinking water, but it can also reduce pollutants that are found in tap water. By installing a New Wave Enviro Water Filter, you can help to protect your family’s health and the environment.
Components Of New Wave Enviro Water Filter
- Filter cartridge
- Diverter valve
How To Install New Wave Enviro Water Filter?
Unscrew and remove the existing aerator: Unscrew the aerator from your faucet, and remove it.
Screw diverter valve threads onto the faucet: The new wave enviro water filter kit comes with a diverter valve, which screws onto the end of your kitchen faucet about halfway down the threads. To attach it to the faucet, you will need a screwdriver or wrench for tightening. Hand-tighten the diverter onto your existing faucet until it is friendly and secure.
Also, include a male thread adaptor: it connects the new filter to your water pipe. The thread adaptor fits between the filter and the existing plumbing connection. It is essential to use a male thread adaptor to ensure that all water filter components are correctly connected. Once you have attached the thread adaptor, secure it with teflon tape, so there are no gaps or spaces.
Turn on water: The next step in installing a New Wave Enviro Water Filter is to turn on the water. This can be done by turning on the water supply valve and letting it run for two minutes to flush out any debris in the pipes.
Pull the PIN in the diverter: Locate the diverter valve under your sink to begin the installation process. Pull the pin and turn it down, so the water pressure is released from the existing plumbing system.
Flush the water: Start flushing the water through your system before installing a new wave enviro water filter. This will help remove any dirt or rust particles that might have built up in the pipes.
Hand tightens where leakage occurs: 1/4 turn] at the point of leakage, using a wrench or adjustable pliers if necessary. If the filter is now secure, open the main water supply and allow it to run for five minutes before checking again for any leakage.
How Do You Replace The New Wave Enviro Water Filter?
Exchanging the filter is easy and should be done every six months to maintain water quality. Before you exchange the filter, make sure you have a new one. To exchange the filter:
Step1:Turn off the feed valve and release pressure from the system by opening any faucet.
Step 2: Unscrew the outer housing and filter assembly from the filter head.
Step 3: Remove the old filter and discard it responsibly.
Step 4: Install the new filter by lining up the grooves on the filter and head, then twisting to secure it.
Step 5: Re-attach the outer housing and turn on the feed valve.
Step 6: Run water for 2-3 minutes to flush out any debris in the system and ensure your filter works correctly.
Which Things Do New Wave Enviro Water Filters Remove?
Trihalomethanes: This includes compounds such as chloroform, bromodichloromethane, dibromochloromethane, and others. They form when chlorine or other disinfectants used to control microbial contaminants in drinking water react with naturally occurring organic and inorganic matter in water.
Chlorine: The New Wave ENVIRO water filter utilizes an activated carbon block to reduce chlorine and sour taste.
Lead: New wave enviro water filters offer a simple way to ensure your drinking water is filtered and free of lead.
Mercury: Mercury is a toxic heavy metal found in the environment, and it can enter your water supply if you are on a public system. Installing a New Wave Enviro Water Filter is an effective way to remove mercury from your drinking water.
Cadmium: If you want to install a New Wave Enviro water filter, it is essential to know how it can affect your system. Cadmium, an element found in many natural and artificial products, can leach into drinking water and cause serious health problems if consumed over extended periods. New Wave Enviro water filters are designed to reduce or remove the presence of this toxic metal from your drinking water.
Is this a reverse osmosis system?
No, the New Wave Enviro Water Filter is not a reverse osmosis system. Instead, it utilizes an activated carbon block to reduce chlorine, bad taste, and odor. It also utilizes a media filter which reduces lead and other contaminants in drinking water.
Can it filter out fluoride?
Yes, the New Wave Enviro water filter can remove fluoride from your water. It uses a two-stage filtration process that removes 99% of all fluoride in the water.
How much water should I flush before drinking water?
Before drinking water filtered through your New Wave Enviro Water Filter, it is recommended to flush the filter with at least three gallons of cold water. This helps clear out any contaminates that may be present in the carbon media or other filtration components.
Can the on and off knobs be replaced?
Yes, the on and off knob can be replaced. To do so, first, turn the water supply off to the filter system. Then remove the hose connections in front of the filter and all parts, including the heads attached to it. You will find that two screws hold the knob firmly in place.
Installing a new wave enviro water filter is a great, cost-effective way to ensure that you and your family drink clean, safe water. You can have your filter up and running in no time with just a few simple steps. Follow all instructions carefully and regularly change your filter cartridges for optimal performance. Enjoy cleaner, better-tasting water with the new wave enviro water filter.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.