How To Install Pelican Water Filter?

Installing a Pelican water filter system is an easy and cost-effective way to improve the quality of your drinking water. Pelican filters are designed for residential applications, providing you with better-tasting water than tap or bottled options. Installing a Pelican filter can be done in just a few steps.

What Is Pelican Water Filter?

A Pelican Water filter is a filtration system to remove impurities and contaminants from drinking water. It uses an activated carbon filter, which can be used to reduce chlorine taste and odor, as well as improve the color, clarity, and freshness of your water. Pelican Water filters are suitable for both residential and commercial applications. They are designed to be easy to install and provide effective drinking water filtration. Pelican Water filters are available in various sizes, allowing you to choose the right one for your needs.

Parts Of Pelican Water Filter

• Sediment filter
• Wrench
• Non-abrasive auto wax
• Bypass valve
• Hose bib assembly

Installing Hole House Pelican Water Filter

Installing Carbon soak

Step1. Attach a garden hose to the Hose Bib Assembly: Connect one end of the hose to the Hose Bib Assembly located at the top of the Pelican Filter System.

Step2. Connect the Hose Bib Assembly to Bypass Valve: Once the filter housing is firmly secured, attach the Hose Bib Assembly to the inlet side of the Bypass Valve.

Step 3. Fill the Pelican Whole House Water Filter slowly: Once the filter is attached to your plumbing system, use a garden hose to fill the filter with water. Make sure you don’t fill it too quickly, or the pressure will become too high and could cause damaging leaks in your system.

Step 4. Turn the water off: Once the old filter has been removed, turn off the water supply.

Step 5. Remove the garden hose from the Hose Bib Assembly: Disconnect the garden hose from the Hose Bib Assembly. The Assembly is located at the bottom of the Pelican Water Filter and consists of two parts, an inlet fitting and an outlet fitting. The garden hose should be connected to the outlet fitting of the Hose Bib Assembly.

Step 6. Soak the carbon tank for 48 hours: After connecting it to the filter, it is essential to let it soak for 48 hours. This will help the water absorb the activated carbon, which helps remove bacteria and other contaminants from your water supply.

Installing Carbon Flush

Step 1. Reattach the garden hose: Reattach the garden hose to the inlet flow control valve. Make sure that the connection is tight and secure.

Step 2. Slowly turn on the water: Next, turn on the water slowly. This will raise the pressure inside the filter and will cause any air pockets to be released.

Step 3. Run water through the inlet side of the Bypass Valve: Connect the inlet side of your Bypass Valve to the cold water supply line. Make sure that you connect it securely, so there are no leaks.

Step 4. Turn off the water: Once the filter is in place and your connections are secure, turn off the water supply.

Step 5. Remove the Hose Bib assembly: Hold the Hose Bib assembly, then turn it counterclockwise to loosen and remove. Discard the old Hose Bib assembly, as it is no longer needed.

Step 6. Slowly, fully open the hose spigot: Let the water run through the filter until it has emptied. This will ensure that the filter is full of fresh water. You can also flush out any debris or sediment from the system.

Step 7. Run the water through the outlet: Connect the outlet hose to an open tap and turn it on. Let the water run through the filter for approx Five minutes before using it. This allows the carbon block filter to wash away any impurities that may have been collected during installation, giving you clean and pure drinking water.

Step 8. Turn off the water: Once the connection is completed, turn off the main water supply to your house. This will ensure no water escapes from the system while installing or replacing filters.

Step 9. Remove the Hose Bib Assembly from the Bypass Valve: Disconnect the hose bib assembly from the bypass valve by unscrewing it with a wrench. Please keep track of any washers or gaskets that come off with it. If needed, replace them with new ones before reinstalling the hose bib.

Sediment Filter Assembly

Step 1. Unscrew the cover from the Blue Filter Housing: Locate the Blue Filter Housing on the cold water line connecting to the Pelican whole house water filtration system. Unscrew the cover from the blue filter housing.

Step 2. Remove the plastic covering from the Sediment Filter: Remove the plastic covering or packaging from the Sediment Filter. Remove any tape holding the wrap, then cut away the plastic around the filter using the scissors.

Step 3. Place the Sediment Filter onto the Stand Pipe: Take the Sediment Filter and place it onto the Stand Pipe. Ensure that the filter has been attached adequately before continuing with the installation process. Make sure to tighten all parts firmly and securely to ensure the proper performance of the water filter system.

Sediment Filter Installation

Step 1. Shut off the water: Turn off the main water supply to your home.

Step 2. Attach the Filter Cover to the Mounting Bracket: Once you have installed the mounting bracket, slide the filter cover onto the bracket. Ensure all four tabs of the cover are inserted into the slots on the bracket. Then turn each knob in an up-and-down motion to secure it and ensure all knobs are tightened securely.

Step 3. Attach the Mounting Bracket to the wall: Once you have chosen a location for the filter, use the screws that came with the kit to attach the mounting bracket to the wall. Make sure it is securely mounted in place before continuing.

Step 4. Hand tightens the Blue Filter Housing: After the Blue Filter Housing is correctly aligned, use your hand to tighten it until it is secure. If a wrench is used in this step, you risk stripping the filter housing threads.

Step 5. Determine the size of your inlet water supply line: To install the Pelican Water Filter properly; you must determine the size of your inlet water supply line. This will help you choose the right fittings and adapters to complete the installation. Use a measuring tape or ruler to measure the inside diameter of your inlet water supply pipe and record this information for later use.

 Whole House Water Filter Tank Installation

Step 1: Level the pelican whole house water filter.

Step 2: Install the fitting onto the inline.

Step 3: Connect the incoming water supply with the bypass valve.

Step 4: Open a cold water faucet.

Step 5: Turn on the water supply.

Step 6: Allow the tank to soak.

Step 7: Flush the system with running water.

Step 8: Check for leaks.

Installing a 3-stage pelican water filter

Parts of 3-stage pelican water filter

• Feed valve
• Green feed water tubing
• Blue product water tubing
• GAC carbon filter
• Sediment pre-filter

Turn off the cold water supply: Ensure to turn off the cold water supply valve before installing your pelican water filter.

Relieve pressure: Open the hot and cold water faucets to relieve any pressure in the pipes.

Install the feed valve assembly: Install the feed valve onto the cold water outlet fitting, making sure to wrap it in the plumber’s tape. Secure the top of the feed valve assembly to the cold water line using an appropriately sized hose clamp and tighten it with a screwdriver. Then connect the hot water line to the other end of the feed valve Assembly.

Press green tubing into the feed valve assembly: Once the filter head is securely installed, you can press the green tubing into the feed valve assembly. It should be inserted for a few inches until firmly in place. Make sure there are no gaps or spaces between the tube and the feed valve assembly so that water does not leak out of your pelican water filter.

Connect the cold water faucet with the feed valve assembly: Attach the feed valve assembly to the end of the cold water line. The feed valve assembly will have a threaded fitting on either side – one side should be connected to the cold water line, and the other will be used to attach your filter system.

Turn on the feed water valve: Once the filter is in place and connected to the water line, turn on the feed water valve. Doing this gradually will allow air trapped in pipes to escape before water starts flowing through the filter. This can help prevent damage to filter components due to pressure created by trapped air.

Check for leaks: Check all connections once the water flows through the filter. Make sure all fittings are tight and secure to ensure there won’t be any problems in the future due to leaking water. If there are any leaks, they should be fixed as soon as possible to avoid further damage or contamination from outside sources.

Troubleshooting

Pressure drops during the carbon wash: If the pressure is off during the carbon wash, it may be due to a clogged filter. To check if the filter is clogged, turn the water off at the main inlet and open all faucets throughout your home. Once no more water flows from any of them, disconnect the filter from its housing unit and inspect it for debris. If any debris is found, clean the filter before reinstalling it.

Water leaking at the top of the tank around the head: If you notice water leaking at the top of the tank around the head of the Pelican Water Filter, it is likely due to an issue with the O-ring seal. To fix this, you will need to replace the O-ring. Turn off your main water supply before attempting any repairs. Carefully remove the filter head from the filter tank. Unscrew the O-ring and discard it. Then, take a new O-ring and lubricate it with food-grade silicone or Vaseline. Place the O-ring inside the groove on the filter head and screw it back into place until tight; do not over-tighten, as this can damage the O-ring.

The tank leans to one side or is not level: If the tank leans to one side or is not level, you need to ensure it is properly leveled before attempting to install your Pelican water filter. To do this, you can use a spirit level placed on the top of the tank and adjust the legs or feet of the tank until it is perfectly balanced. You may also need to adjust the legs or feet to ensure they are leveled. Once the tank is level, you can proceed with the installation of your Pelican water filter.

The water inside the tank is gray: If you see gray-colored water inside the Pelican tank, there is likely a build-up of sediment or silt. This should be resolved by replacing the filter and performing a “backwash” on your system.

Water pressure is slowing: You may be slowing when using a pelican water filter. Many things, including clogged sediment in the filter or a system’s blockage, can cause this. To check for these issues, turn off the central water and disconnect the input line from the faucet to the water filter housing. Inspect the filter’s sediment trap and remove any accumulated gunk or debris.

Water appears gray or cloudy: If your water appears cloudy, you will want to install a Pelican Water Filter. The filter reduces chlorine, heavy metals, and sediment from the water, which can make it look cloudy.

Water pressure slows immediately after installation: The Pelican water filter comes with a bypass valve on top of the unit. If your water pressure slows immediately after installation, the bypass valve is likely in the wrong position.

FAQs

In which direction do you turn the water filter to remove it?

To remove the Pelican Water Filter, turn it counterclockwise. It should come off quickly by hand.

How often do you change the pelican water filter?

It is recommended to change your pelican water filter every 6-12 months, depending on how often you use it. The more frequently you use the filter, the sooner you should replace it.

Does water filtration work?

Yes, Water filtration is a highly effective way to remove dirt, sediment, and other contaminants from water. Filtration systems can also remove bacteria, parasites, viruses, and other potentially harmful microorganisms.

Are Pentrait and pelican the same company?

No, Pentrait and Pelican are not the same company. Pentrait is a manufacturer of water filtration systems for home, office, and industrial use and is based in California, USA. Pelican Water Systems, on the other hand, is an international company that provides high-performance water filtration systems for residential and commercial applications.

What does the pelican whole house filter remove?

The Pelican Whole House Filter is designed to remove sediment, chlorine, chemicals, and other contaminants from your home’s water supply. It also reduces unpleasant tastes and odors for better-tasting drinking water.

How much does it cost to install a whole-house pelican water filter?

The cost of installing a Pelican Water Filter will depend on the type and number of filters you choose and any additional components or labor involved. Basic whole-house water filter systems start at around $600 for smaller homes with one filtration system but can be much more expensive depending on your needs.

Conclusion

Installing a Pelican water filter is not difficult, but it does require careful consideration and attention to detail. By taking the time to properly size your system, choose the right filter for your needs, and follow installation instructions correctly, you can ensure that you have a safe and effective filtration system that will provide clean, healthy drinking water in your home.