Pure water inline ice maker water filters are great for improving the taste and quality of the ice cubes produced. Installing one of these filters is relatively simple and can be done in a few easy steps.
For installation, you will need to purchase a filter with the correct connection type for your ice maker. Most filters come with either quarter-inch female or half-inch male connectors.
What Is Pure Water Inline Ice Maker Water Filter?
Pure water inline ice maker water filter is an essential tool to ensure the quality of your drinking water. It helps remove impurities, such as chlorine and sediment, from your tap water before it goes into your fridge’s ice maker. With a pure water filter, you can have crystal clear ice cubes that won’t have a strange taste or smell.
Things Required
- Utility knife
- Towel
- water bucket
- gloves
- filter mounting supplies
- adapters
- Tools
Installing The Filter
Measure the diameter of the water supply tubing: Use a ruler or measuring tape to get the diameter of the water supply tubing. You will use this measurement to determine what type of ice maker filter you need to buy.
Choose a place to mount the water filter: Before beginning the installation process, you must decide where to mount your filter. You can either mount it horizontally or vertically.
Unplug the refrigerator: The initial step to installing a pure water inline ice maker water filter is to unplug the refrigerator. If it is hard-wired, then you should turn off the circuit breaker that controls the refrigerator. This will ensure that you are safe while working on your refrigerator and help prevent any damage from being done.
Shut off water supply: To install your inline ice maker water filter, you must first shut off the water supply by turning off the main shut-off valve.
Cut the water supply tube: locate the water supply tube near your refrigerator and cut it. Ensure the water supply tube is clean before cutting; use a cotton swab to remove any fluid or debris if necessary. Cut the water supply line with a utility knife, careful not to damage the tube.
Clean the ends of water tubing: Before you install the pure water inline ice maker filter, it is essential to inspect and clean the ends of your water tubing. If mineral deposits or kinks are in the tube, use a brush and detergent solution to remove them before attaching the filter.
Push the inlet end of the water tube into the fitting: Once the tubing is correctly connected to the water source, you can install your pure water inline ice maker water filter. Start by pushing the inlet end of the water tube into the fitting on top of the filter unit. Ensure that it is securely attached and won’t come off quickly.
Tug the water tube: Tug lightly with the attached water tube to ensure it is appropriately connected. If you find that your water tube is not securely connected, make sure to reattach it and try tugging it again.
Shut off the water supply valve: Before installing a pure water inline ice maker water filter, it is essential to shut off the water supply valve. To do this, locate the main water line and turn off the valve. Make sure that no additional water enters your house while installing the filter. This will prevent any potential messes from occurring and ensure that no water leaks during the installation process.
Connect the outlet tube to the filter: Once you have installed the filter, it is time to connect it. It is essential to ensure the tube is firmly connected and sealed adequately for your water to flow correctly through the filter.
Open the water supply valve: Installing a pure water inline ice maker water filter is to open the water supply valve. Depending on the model of your filter, this will be either under the sink or surface mounted near the refrigerator.
Check for leakage: Once you have installed the pure water inline ice maker water filter, it is essential to check for any leakages in the filter.
Push tube if water leaks: If you experience water leaks from the push tube after installing your Pure Water Inline Ice Maker Water Filter, push the tube firmly onto the fitting. If it leaks, you may need to check if the O-ring is properly in place and replace it if necessary. You can also try tightening the nut where the tubing connects to the filter housing. If your water leak persists, contact us for help troubleshooting the issue.
Attach the filter to the mounting hardware on the wall: Once the filter is in place, you’ll need to attach it to the mounting hardware on the wall. This can usually be done with two screws or bolts. Make sure that they are tightened firmly and securely, as any loose fittings could result in water leaking out of the filter or seeping into other areas of your home.
Plug the refrigerator: Insert the plug of the water filter into a working outlet.
Flush the filter: Once it has been installed, flush it with cold water for a few minutes to ensure it is working correctly and thoroughly. Flushing the filter removes any impurities or sediment which may be found in the water supply. After flushing, discard the first few gallons of filtered water before making ice or other beverages.
FAQs
How does the water filter replacement indicator work?
When your inline ice maker water filter needs to be replaced, a red indicator light will appear on the system. The indicator light is triggered when the filter has reached its maximum capacity and can no longer reduce contaminants from the water.
Can water filters get moldy?
Yes, water filters can get moldy. Mold and bacteria buildup in the filter is one of the most common problems with water filters — if not regularly cleaned or replaced. If a filter isn’t replaced when it’s supposed to be, it can become clogged over time and cause mold growth inside the system.
Why doesn’t the filtered water taste like pure water?
This is a common problem and can be caused by several factors. For example, the filter may not be compatible with the type of water you are using, or it may not have been installed correctly. It could also be that your tap water contains minerals that are not removed through the filtration process.
How often do you change the whole house water filter?
When installing a Pure Water Inline Ice Maker Water Filter, it is essential to change the filter regularly to maintain its effectiveness. Ideally, the filter should be changed every six months or when you notice a decrease in water pressure from your ice maker.
Are water filters bad for faucets?
No, water filters are not bad for faucets. Installing a filter system can help to protect your faucet from sediment and other contaminants that accumulate over time.
Do all refrigerators with ice makers have filters?
No, not all refrigerators with ice makers have filters. Some models are manufactured without a filter system. It is essential to check if your refrigerator has an inline water filter before attempting to install one.
Conclusion
Using a water filter with your ice maker is essential in ensuring that the ice you produce is clean and free of contaminants. A quality water filter will eliminate impurities, chlorine, sediment, rust, and other compounds from your drinking water before it reaches the ice maker. This not only improves the taste of your ice cubes but also eliminates potential health hazards. Furthermore, using a water filter can extend the life of your ice maker and ensure that it produces clean and safe ice cubes for you to enjoy. Therefore, investing in an inline ice maker water filter is highly recommended if you want the best-tasting ice cubes and peace of mind knowing they are safe to consume.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.