How To Install The Franke Water Filter?

The Franke water filter is a great way to get clean and healthy drinking water in your home – by removing chlorine and other impurities, reducing limescale build-up, and improving the taste of your tap water. Installing a Franke water filter is easy, and you can enjoy healthier drinking water in no time.Before beginning the installation, it’s essential to ensure you have all the necessary parts for a successful setup. These include the mounting bracket, filter cartridge, screws, washers, and an appropriate wrench for tightening nuts or bolts.

What Is A Franke Water Filter?

What Is A Franke Water Filter
A Franke Water Filter

Franke water filter is a modern, innovative kitchen device that provides clean and safe drinking water. This product uses advanced filtration systems to remove contaminants from your tap water, giving you great-tasting drinking water without any impurities. The Franke Filter also has an easy-to-use design, allowing quick and easy filter changes when necessary.

How Does A Frank Water Filter Work?

How Does A Frank Water Filter Work
A Frank Water Filter Work

The Franke water filter uses granulated activated carbon (GAC) filtration to remove chlorine, taste, and odor from your drinking water. The GAC is a highly porous material that traps particles more significant than the pores themselves, such as impurities like chlorine, which can make water taste bad. The water then passes through a fine mesh filter that traps even smaller particles. The result is cleaner and better-tasting water, free of contaminants.

The Franke water filter also has a built-in scale inhibitor to reduce limescale in tap water. Limescale build-up can cause blockages in pipes and fixtures, reducing water flow and making cleaning difficult. The scale inhibitor helps fight limescale, giving you more transparent and healthier water.

How To Install The Franke Water Filter?

Shut off the main water supply
Shut off the main water supply

Shut off the main water supply: Shut off the water supply to your home before starting the filter installation.

Install the stop valve
Install the stop valve

Install the stop valve: After unboxing the filter, locate the stop valve and prepare for installation. The stop valve should be placed after the cold water shut-off valve to make it accessible when needed. Make sure to secure it with a pipe clamp or similar fastening method.

Install the filter cartridge: Install the filter cartridge over the outlet pipe. Make sure the O-ring is placed correctly and that the ends are tight. Secure the cartridge to the filter housing with a screwdriver if needed.

Assemble the filter housing: Identify the Inlet and Outlet connections on your Franke Water Filter Housing and connect the appropriate supply lines. Tighten the water filter housing with a wrench, hand-tightening each nut until it is finger-tight, then turn it one or two more to ensure a snug fit.

Connect the filter housing to the stop valve: Using the supplied isolator valve, connect the filter housing to the stop valve. Make sure you tighten it slowly and evenly, then give it a final quarter-turn to ensure it is adequately secured.

Connect the filter housing to the filter tap
Connect the filter housing

Connect the filter housing to the filter tap: Once you have chosen the location for your Franke water filter, the next step is to install it. The first thing to do is connect the filter housing to the filter tap. Make sure that there are no leaks and screws are tightened securely.

Secure the filter housing bracket: Once you have attached the filter housing to the water supply lines, it is time to secure the bracket. To do this, use the screws provided with your Franke Water Filter system. Secure them firmly and evenly, ensuring they are not over-tightened or under-tightened. Check that the bracket is sitting level by using a leveler.

Turn the water on: Once you have successfully installed the Franke water filter, it is time to turn on the water. Make sure that all connections between the inlet and outlet hoses are secured tightly. Turn the valve of your primary water source in a clockwise direction until you feel resistance.

Check the installation for leaks: After installation, check the filter for any leaks from the connections and ensure that these are properly sealed.

How To Change The Filter Cartridge Of The Franke Water Filter?

Switch off the power supply: Switch off the power supply to the filter before starting the replacement process.

Shut off the water supply to the filter: Before starting the installation process, switch off the water supply to the filter. This is important to ensure that there is no running water while replacing or installing a new Franke water filter.

Flush the remaining water: Once the new cartridges are secured, you must flush out any air bubbles and sediment from the filter housings. Open all taps connected to your filter system and allow cold water to run through it for around 10 minutes. This will ensure that the filter housing is adequately filled with water and that all of the air has been flushed out.

Unscrew the sumps: Unscrew the sump at the top of your Franke filter, keeping it level.

Remove the old cartridge: To install a Franke water filter, you must first remove the old cartridge from the tap. Also, discard the water.

Remove the new filter cartridge from packing: Unpack the new filter from the cartridge from its packaging.

Wet the O seal: Once you’ve assembled the filter, it’s essential to get the O-ring with cold water. This helps ensure a tight seal and prevents leaking.

Please place it in the filter sumps: Place an o seal in the filter sumps and press it firmly.

Position the cartridge into the filter head
Position the cartridge into the filter head

Position the cartridge into the filter head: Once you have the filter head and cartridge ready to go, it’s time to position the cartridge into the filter head. The cartridge should fit easily into the opening of the filter head with a slight rotation until it clicks into place.

Tighten the sump: Once the filter head has been replaced, It’s time to tighten up the sump. This can be done by hand or with an adjustable wrench.


Milky water: The white particles in the water could be caused by the filter not being replaced. Make sure to change it regularly according to the manufacturer’s instructions.

Tiny black specks in the water: If you notice these, it’s time to consider installing a Franke water filter. It will reduce chlorine and other contaminants from your home’s tap water, allowing you to enjoy cleaner, better-tasting drinking water.

Water flow is noisy: If your water flow is noisy, it could be because of a blocked Franke Water Filter. You’ll need to check the filter and clean or replace it as needed to fix it.

The vent assembly is overflowing: If the vent assembly on your Franke water filter is overflowing, you need to adjust the flow rate.

  • Turn off the cold water supply and remove the valve assembly cover.
  • Loosen the screw on top of the stem using a flathead screwdriver; this will loosen and lower the stem.
  • Slowly turn it down until water stops flowing from the vent.
  • Replace the cover and turn on the cold water supply.


What is the water flow rate of the filter?

The Franke water filter has a flow rate of 1.2 gallons per minute.

What is the temperature range for optimal performance?

The Franke water filter works best at temperatures between 40-100 degrees Fahrenheit.

Which type of filter cartridges are compatible with Franke filters?

Which type of filter cartridges are compatible with Franke filters
filter cartridges

Franke water filters are designed to be used with Franke-compatible filter cartridges. These cartridges come in various shapes and sizes, including the popular FKF10, FKT20, and FKH30. Depending on your specific needs, you may purchase additional filter cartridges for your Franke filter.

Do I need to purchase additional parts for installation?

You do not need to purchase additional parts to install your Franke water filter. The filter comes with all the necessary components for installation, including a mounting bracket, screws, and gaskets.

Can I install the filter with existing plumbing lines?

The Franke water filter is designed to be installed with existing plumbing lines. Your setup may require additional parts, such as fittings, hoses, and valves.


Installing a Franke water filter is an easy task that can be accomplished in just a few simple steps. Always follow the instructions carefully and always take safety precautions for installation. Once you have completed the installation, you can enjoy cleaner, healthier drinking water with the help of your own custom-installed Franke water filter system.

Leave a Comment