Installing a water filter in your Jenn Air refrigerator is a straightforward process that only takes a few minutes. You can locate the dedicated compartment for the filter in your refrigerator. Depending on the model, it may be found inside the main refrigerator section or at the bottom of the refrigerator door. You can install the water filter in the filter house by inserting it firmly.
What Is Jenn Air Refrigerator?
Jenn Air is a refrigerator brand known for its high-end appliances. Their refrigerators come with an innovative design that allows you to access the water filter quickly and easily. Some models also feature a dedicated water filter compartment, making it even easier to change your filters regularly. This makes them ideal for households looking for efficient ways to purify their water and maintain the quality of their drinking water.
How To Install Water Filter In Jenn Air Refrigerator?
Unplug the refrigerator: Unplug the refrigerator from its power source before starting the installation process.
Locate the water filter: Most Jenn Air refrigerator models have the water filter located in the grille at the base of the fridge, near the floor.
Rotate the old filter 1/4 counterclockwise: Locate the water filter on your refrigerator. It should be located in the top right corner of the refrigerator behind a cover flap. Once you have located it, rotate it 1/4 counterclockwise until it stops. This will unlock the filter and allow for removal. Grab the base of the filter and pull it straight out to remove the old filter.
Remove new filter from packaging: Once it has been obtained, remove it from the packaging and discard the old filter.
Gently push the filter up to insert in the housing: The arrows on the filter should point toward the inlet valve. Make sure it is securely in place. If you do not feel any resistance, remove it and try again. The filter must be inserted adequately for water to reach your refrigerator’s ice maker and drinking area.
Flush out the filter: After removing the old filter, flush it out with cold water for about three minutes. This will ensure that all of the dirt and sediment from the old filter is cleared away before installing a new one. Remember to discard any water accumulating in the sink or basin during flushing.
Reset the filter button: Once the new filter is in place, press and hold the “Filter Reset” button for 3 seconds. The indicator light should reset to show that the water filter has been replaced.
Press the child lock button: On the inside console towards the top of your Jenn Air refrigerator. This will unlock the water filter compartment.
Drink the freshwater: Now, you can drink fresh water from your refrigerator.
How To Reset The Water Filter Date On Jenn Air Refrigerator?
Step1: Unplug the fridge and locate the filter reset button on the upper side of the water filter housing.
Step2 : Press and hold down the Reset Filter button for several seconds until you hear a click, indicating that it has been reset.
Step 3: Plug your refrigerator back in to power up the system and confirm that all display settings have returned to their defaults.
Step 4: Press and hold the Reset Filter button again for several seconds until you hear a click, indicating that it has been reset.
Step 5: Afterward, enter the date you last changed your filter and press ‘OK.’ This will ensure that the filter will always remind you when it’s time for a replacement.
Troubleshooting And Fixing
Leaking of water: If your water filter leaks, there are a few possible causes. The first cause could be that the filter is not installed correctly. Check the filter installation instructions provided with your refrigerator and ensure that everything is securely in place. Another possibility could be that the O-ring seal (or other parts of the filter) is not seated correctly or has become damaged.
Slow flow rate: If your water filter is installed correctly, but you experience a slower-than-usual flow rate, the issue could be caused by a clogged filter. This can happen when filters aren’t replaced regularly or if there is sediment in the water line. To resolve this issue, try replacing the filter with a new one and flush 2 gallons of water through it before using it. If the issue persists, it may be time to check your water line for any blockages or sediment buildup.
Not filtering water: If you are not filtering your water, you may consume contaminants that can cause health problems. Installing a filter in your Jenn Air refrigerator is easy to ensure the water and ice taste great while eliminating potential hazards.
FAQs
Where is the filter in the Jenn air refrigerator?
The water filter is located on the upper right side of the refrigerator. You will need to open the freezer drawer until it locks for you to access it.
My new Jenn air filter is not filtering water. How can I solve it?
You will need to check the water pressure. Low water pressure can cause filters not to filter correctly. If this is the case, you may need to contact a certified plumber to increase your water pressure.
How can I know the model number of my refrigerator?
To determine the model number of your Jenn Air refrigerator, you can do one of two things: First, check your fridge’s back or side panel for a label that will have both the product name and the model number listed. Alternatively, if you cannot locate the label on your unit, you can look up the model number online by visiting the Jenn Air website and searching for your specific product.
Where can I get the replacement cartridge?
Replacement cartridges are available through various retailers, including your local hardware store, home improvement center, or online.
Conclusion
Installing a water filter in your Jenn Air refrigerator is a simple process. With the right tools and parts, you can easily have clean and filtered water at your fingertips in no time. Ensure that you disconnect the power supply to the fridge before installation. Once installed, regularly check for any leaks or other issues. Doing so can ensure your filter is always functioning optimally and provide cleaner, healthier water for you and your family to enjoy.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.