Watts Whole House Water Filter is a type of filtration system that helps to purify your home’s water supply. It removes sediment, chlorine, and other contaminants before entering your taps and appliances. This makes sure you have clean and safe drinking water that won’t cause any health problems. Installing a Watts Whole House Water Filter can be a great way to ensure your family always gets clean and safe water. Fortunately, the installation process is relatively simple and can be done in just a few steps.
How Does Watts Whole House Water Filter Work?
Watts Whole House Water filters use a multi-stage filtration process to remove impurities from your water supply. The first stage is a sediment filter which reduces the amount of dirt, rust, and other particles in the water. This is followed by a second-stage carbon filter which removes chlorine, pesticides, herbicides, and other organic compounds. The final filtration stage uses a sub-micron filter which removes bacteria and other microorganisms from the water.
Parts Of Watts Whole House Water Filter
- Filter housing
- Built-in bypass valve
- Filter wrench
- Mounting bracket
Tools Recommended For Installation
- Hacksaw
- Pipe cutter
- Sandpaper
- Plumbers tape
- Wrench
How To Install Watts Whole House Water Filter?
Determine placement of the unit: The Watts whole house water filter should be installed after your main shut-off valve and before any other plumbing fixtures you wish to have filtered.
Gather the parts: Before installation, it is important to ensure that all necessary parts are included with your purchase. This includes a brass mounting bracket, two stainless steel screws, an inlet and outlet adapter, a filter wrench, a pressure gauge, and the Watts whole house water filter.
Shut off main water supply: Before beginning the installation of a Watts Whole House Water Filter, you need to shut off your main water supply. This will ensure that no water is running through the system while you are working on it.
Relieve the water pressure: Reduce the pressure of the water in your home. To do this, turn off the main water shut-off valve and open up a few faucets to release residual pressure.
Cut the water line where the whole house water filter should be installed: Turn off the main water line. -Cut the pipe where you would like to install the filter. Use a hacksaw or pipe cutter, then clean up any rough edges with sandpaper.
Plumb the system to the waterline: The next step is to run a waterline from the cold water line to the Watts Whole House Water Filter. This will ensure that all the water coming into your home is filtered. You’ll need to use compression fittings and thread sealant for this task. Make sure you use brass or copper piping for the best results.
Make sure the valve on the lid is turned to the filter: Once you have obtained the Watts Whole House Water Filter, it is time to install it. To begin the installation, ensure that the valve on the filter’s lid is turned to the “Filter” position. This will ensure that water can pass through the filter and be filtered properly.
Open a faucet downstream of the filter unit: Place a bucket below the faucet to catch the water. This will ensure that you have an adequate supply of water downstream so that contaminants are flushed out with the backwashing process.
Please turn on the main water supply slowly: Turn on it slowly, as opening it too quickly can cause a higher pressure than your Watts Whole House Water Filter is designed for. To do this, locate the shut-off valve that supplies the main water line to your home and open it just enough to allow a very slow stream of water into the house. Monitor the pressure gauge to ensure it is below the designed limit for your filter, typically around 60 psi. You can adjust the shut-off valve to reduce the pressure before installing it.
Turn off the faucet and check for leaks: To begin, turn off the faucet to your existing water supply line. Open up the faucet and inspect it for any signs of leaks or damage. If there are any signs of a leak, replace the hose as soon as possible before proceeding with the installation.
Watts Whole House Water Filter Replacement
Shut off water to the filter housing: Locate the main shut-off valve for the house water supply and turn it counterclockwise to close.
Remove the bowl by turning it clockwise: Once the two screws have been removed, you can turn the bowl clockwise until it comes loose. Be careful not to drop it as it may break.
Lose the housing with filter wrench: Once you have the Watts Whole House Water Filter Housing, it’s time to install the filter in your home. The housing should have all the necessary tools and pieces to install the filter. The first step is to loosen the housing with a filter wrench, which may be included or purchased separately.
Remove the old filter and discard: Before installing the new Watts Whole House Water Filter, it is essential first to remove any existing filter. To do this, shut off the incoming water supply (typically from a city central or well) and open a nearby faucet to release pressure in the water line. Now, unscrew the old filter by turning it counterclockwise and discard.
Clean the filter housing with soap: Before installing the Watts Whole House Water Filter, it’s essential to clean the filter housing thoroughly. You can do this by using a mild soap and water solution inside and outside of the housing. Once it is cleaned, rinse any excess soap residue with clean water and allow it to dry completely.
Lubricate O-rings with water: Before installing the Watts Whole House Water Filter, it is important to lubricate both O-rings with water. This will help ensure that the filter does not leak and keeps a strong seal.
Replace the filter: Now install the new filter opposite to how you removed the old one. You can use a wrench to tighten it firmly.
Reinstall the filter bowl: Once the filter cartridge has been replaced, the filter bowl of your Watts Whole House Water Filter needs to be reinstalled. To begin this process, make sure that the valve is in the ‘off’ position and that no water is running through it. Once you are certain that the valve is off, unscrew both ends of the bowl from the housing. Once removed, please insert the new filter cartridge into the bowl and make sure it is seated firmly.
Turn the bypass valve back to “FILTER”: After the filter cartridge is installed, turn the bypass valve back to “FILTER.” This will ensure the filtered water passes through the Watts whole house filter.
Test for Leaks: After installation, check all connections for leaks. If any are found, tighten or replace as needed using Teflon tape and pipe thread compound.
Flush the Filter: Once the filter system is installed, flush it out with a hose or bucket to ensure the interior of the cartridge is cleaned correctly and free from any debris. This will help improve the longevity and performance of your Watts Whole House Water Filter.
Troubleshooting
Filter bowl has no water in it:
- Check the shut-off valves to make sure they are both open all the way.
- Check that the bypass valve is in the filter position.
- Make sure there is no sediment build-up on the screens; clean or replace them.
- Test your water pressure; if it’s too low, consider installing a booster pump.
Leaking at the bowl: If you are experiencing leaking at the bowl, it is likely because there is an issue with the seal between the filter housing and the bowl. To rectify this, loosen all the screws holding the bowl to the filter housing and remove the bowl from its mounting hardware. Inspect all seals for any signs of damage or wear and replace them if necessary. Once all seals are intact, reinstall the bowl and filter housing, making sure to tighten the screws enough that there is a secure fit with no leaking.
Leaking at the valve fitting: If, after installation, you notice water leaking from the valve fitting, it is likely because the fittings are not properly tightened. Try tightening them with a wrench or pliers to ensure a tight fit while holding the housing in place with your other hand. If this does not stop the leak, you may need to replace the O-ring. Make sure the O-ring is the correct size and fits snugly into the fitting, then tighten the fitting again with a wrench or pliers until it is secure. You should also check that all other fittings are securely tightened to avoid further leaks.
Low water flows: If your Watts Whole House Water Filter is experiencing low water flow, it may be due to one of the following:
- The filter is clogged. Change the cartridge and clean the housing if this is the case.
- Your water pressure could be too low or erratic. If so, consider installing a booster pump to increase the water pressure.
- The filter may be installed improperly. Ensure all fittings are correctly connected, and there is no leakage or blockage in the line before installation.
- If you have recently changed your filter, allow a few days for the flow rate to stabilize before adjusting it again.
FAQs
Where should a whole-house water filter be installed?
A whole house water filter should be installed at the point of entry, where your main water line enters your home. This ensures that all the water you consume in your home is filtered.
Do you need a RO if you have a whole house filter?
Yes, some homes may need an additional reverse osmosis (r/o) filter system if they have a whole-house water filtration system. If you are on city water with high contaminants, a r/o system is the better option to remove the pollutants that your whole house filter cannot.
Do the filters have color labels?
Yes, the filters in Watts Whole House Water Filters have color labels. The Standard models are labeled blue, while the Premium models are labeled black. This helps to identify which type of filter is being used efficiently and makes it easier to change the filter when it’s time for a new one.
Why is there water leaking from the top of the valve?
The most likely cause of water leaking from the top of the valve is a worn-out or damaged O-ring seal. This often happens when filters are not changed frequently enough and can result in contaminants entering your home’s water supply. To fix this, you’ll need to replace the O-ring with a new one.
What would cause the leaking at the valve fitting?
The most common cause of leaking at the valve fitting is improper filter installation.
How much electricity does a water purifier consume?
The electricity consumption of a water purifier will depend on the type and model you have. The more complex the filtration system, the higher it will consume electricity, so choosing one that suits your needs is best.
How long does the PUR water filter take a gallon?
The Watts Whole House Water Filter System typically takes about one gallon of water to run through the filter before it is fully activated. Depending on your water pressure, this could take anywhere from a few minutes to several hours.
Is it worth getting a whole-house water filtration system?
Yes, a whole-house filtration system allows you to enjoy clean and safe drinking water from every tap in your home.
Conclusion
Installing a Watts Whole House Water Filter system is a great way to ensure that you have safe, clean water running through your home. With its easy installation, you can rest assured that your family will have access to the best quality water possible. With the proper guidance and preparation, you can enjoy clean, filtered water in your home with minimal effort.
Meet Jeffrey B Roberts, your dedicated guide into the realm of water science and technology. As a hydro biologist with an insatiable curiosity, Jeffrey’s journey has been one of unraveling the mysteries of water systems and advocating for clean, safe water for all.
With an academic background steeped in the sciences, Jeffrey’s passion lies at the crossroads of science, technology, and nature. A deep fascination with plants and genetics has not only enriched their understanding of aquatic ecosystems but has also propelled them into the world of water softening solutions.
Believing that clean water is a basic human right, Jeffrey’s writing transcends the technicalities, making the intricate world of water softening accessible to all. Through their blog, they ardently share insights, tips, and breakthroughs, empowering readers to make informed decisions about their water quality.
Beyond his role as a prolific writer, Jeffrey is a respected figure in the hydronics industry education. With years of hands-on experience, they serve as an adjunct professor, nurturing the next generation of experts at the Thaddeus Stevens College of Technology. His involvement on the Technical Advisory Board further cements their dedication to pushing the boundaries of innovation in water technology.